ESP8285 Nodemcu-M - ESP8285 ESP-M2 / M3 NodeMCU-M ESP8266 Fejlesztés WiFi panel modul Adruino

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
ESP8285 ESP-M2/M3 NodeMCU-M ESP8266 Development WiFi Board Module For Adruino
ESP8285 Nodemcu-M Product introduction:
the Nodemcu-M is completely compatatible with Nodemcu V3 but cheaper than it. the NodeMcu is an open-source firmware and development kit that helps you to prototype your product within a couple of scripts of Lua IOT lines.
the ESP8285-based Development Kit, integrates GPIO, PWM, IIC, -wire and ADC all into a card.
power your developement in the fastest mode combining with NodeMCU Firmware!
USB-TTL included, plug & play
10 GPIO, each GPIO can be PWM, I2C, -wire
FCC CERTIFIED WI-FI Module
PCB antennaProduct Features:
Open-source; interactive; programmable
low price; simple; intelligent
WI-FI enabled
Arduino-like hardware IO
Advanced IO Hardware API, which can drastically reduce redundant work to configure and manipulate hardware
code as ard-uino, but interactively in Lua script
Nodejs Network API Style
Event-driven API for the applicaitons network, which write code developers faciliates running on a 5mm * 5mm Nodejs-style MCU size
greatly accelerate your IOT application development process.
lowest cost WI-FI
Package Include:1 x ESP8285 Nodemcu-M development board ESP8285 ESP-M3What is ESP8285? ESP8285 = ESP8266 1 m, bearing high temperature 125 ℃ (one for ESP8266 just 85 ℃). More importantly, the code programmed in ESP8266 can be used for ESP8285 intactly. The ESP-M3 encapsulates the high performance ESP8285 chip, which equals the ESP8266 chip plus 1 m of flash memory. The ESP825 chip is encapsulated by the extended tensilica's L106 32-bit processor, along with SRAM. The ESP825 has a full and Wi-Fi fuction that can be used alone and alsoused as a slave with other MCU hosters that can start directly from a flash-based. In addition, the built-in high-speed buffer is an allowance for system performance. Especially, the ESP8285 can be used as a Wi-Fi adapter by SPI / SDIO and / or I2C / UART interface, when it is applied to another MCU design.Features Ultra-small size; Support serial to Wi-Fi; Wireless Transparent transmission; Long transmission distance with ultra-low power; Having a high temperature of up to 125 ° C, compared to 85 ℃ for ESP8266.Parameters
SOC characteristics Built-in tensilica L106 ultra-low power 32-bit processor, the main frequency supports 80 MHz and160MHz, and rtos; Built-in protocol tcp / ip; Built-in one channel 10-bit high-precision ADC; Hanging interface: hspi, UART, I2C, I2S, IR remote controk, PWM, GPIO; Deep sleep current 10uA, the cutoff current is less than 5uA; Service, connect and transfer the data packet for 2 ms; To consume power less than 1.0 MW (DTIM3), when on stand by status; Built-in 1 m bytes for SPI flash memory.Wi-Fi Features Support 802.11 B / G / N / E / I; Station support, soft AP, soft mode AP sta; Support for Wi-Fi Direct (P2P); Support for ccmp (CBC-MAC, calculation mode), TKIP (mic, RC4), WAPI (SMS4), WEP (RC4), CRC, etc., for hardware acceleration. P2P search, P2P Go mode / gc mode and P2P power management WPA / PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4 GHz); 802.1 h / RFC1042 Encapsulation of the frame; Support seam less roaming; Support for remote updates and cloud updates (OTA); Support for Smart config functions (including Android and iOS devices).Interface Module 2 * UART; 1 * ADC; 1 * en; 1 * wake pin; 1 * hspi; 1 * I2C; 1 * I2S More than 10 * gpiosOperating temperature: -40 ℃ - 125 ℃;
Module size: 26.8 mm * 16 mmApplication Electronic devices; Smart Power Plug, smart light; Infant monitor; Sensor networks; Security id tags; Wireless location beacon; Home automation; Mesh networks; IP video camera; Portable Electronics; Wireless recognition location; Industrial wireless control; Package Included: 1 x ESP-M3 ESP8285 Serial Wireless Wi-Fi Transmission Module Compatible with ESP8266
401590802585/1 - ali110 (281)