Alacsonyabb ár! 3X (1set színes, véletlenszerű 3D nyomtatókészlet, RAMPS 12864 LCD vezérlő, MEGA2560 R3 E1H7 Nagyobb
Előző

3X (1set színes, véletlenszerű 3D nyomtatókészlet, RAMPS 12864 LCD vezérlő, MEGA2560 R3 E1H7

283483289112

Új termék

3X(1set Color Random 3D Printer Kit RAMPS 12864 LCD Controller MEGA2560 R3 E1H7

3X(12864 LCD Controller: This Full Graphic Smart Controller Contains a SD-Card Reader, an Rotary Encoder and a 128 x 64 Dot Matrix LCD Display.You can easy Connect it to your Ramps Board using the "Smart Adapter" included.After Connecting this Panel to your Ramps you don`t need your pc any more, the Smart Controller Supplies Power for your SD card.
Further more all Actions like Calibration, Axes Movements can be Done by just using the Rotary Encoder on the Smart Controller.
Print your 3D Designs without PC, just with a G-Code Design Stored on the SD Card.
RAMPS 1.4: Fully Assembled & Tested, No Soldering Required.The Modular Design includes Plug in Stepper Drivers and Extruder Control Electronics on an Arduino MEGA Shield
For Easy Service, Part Replacement, Upgrade-Ability and Expansion.
3D Printer Accessories Set meets most needs.
Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module
color random
Note: Random color, don`t accept the specified color.
Material: metal
Mega 2560 R3 Board:
Microcontroller: ATMEGA2560-16AU
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
A4988 Stepper Motor Driver:
Suitable for driving stepper motors below 8V ~ 35V 2A;
Very simple step direction control interface;
Five different stepping modes: full, half, 1/4, 1/8 and 1/16;
Adjustable potentiometer can adjust the maximum current output, can get better step rate;
Automatic current decay mode detection / selection;
High heat will result circuit cut, undervoltage lockout, crossover current protection;
Ground short-circuit )

Bővebb leírás

0 / 1 / Gyorsan Fogyó termék

18 700 Ft‎

-48%

35 961 Ft‎

Hozzáadás a kívánságlistához

Egyéb infó

3X(1set Color Random 3D Printer Kit RAMPS 12864 LCD Controller MEGA2560 R3 E1H7

3X(12864 LCD Controller: This Full Graphic Smart Controller Contains a SD-Card Reader, an Rotary Encoder and a 128 x 64 Dot Matrix LCD Display.You can easy Connect it to your Ramps Board using the "Smart Adapter" included.After Connecting this Panel to your Ramps you don`t need your pc any more, the Smart Controller Supplies Power for your SD card.
Further more all Actions like Calibration, Axes Movements can be Done by just using the Rotary Encoder on the Smart Controller.
Print your 3D Designs without PC, just with a G-Code Design Stored on the SD Card.
RAMPS 1.4: Fully Assembled & Tested, No Soldering Required.The Modular Design includes Plug in Stepper Drivers and Extruder Control Electronics on an Arduino MEGA Shield
For Easy Service, Part Replacement, Upgrade-Ability and Expansion.
3D Printer Accessories Set meets most needs.
Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module
color random
Note: Random color, don`t accept the specified color.
Material: metal
Mega 2560 R3 Board:
Microcontroller: ATMEGA2560-16AU
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
A4988 Stepper Motor Driver:
Suitable for driving stepper motors below 8V ~ 35V 2A;
Very simple step direction control interface;
Five different stepping modes: full, half, 1/4, 1/8 and 1/16;
Adjustable potentiometer can adjust the maximum current output, can get better step rate;
Automatic current decay mode detection / selection;
High heat will result circuit cut, undervoltage lockout, crossover current protection;
Ground short-circuit )

283483289112 - bestbuy (215)