Szín: F7 Flight Controller - IFlight BLITZ F7 OSD repülésvezérlő BLITZ E45S 4-IN-1 ESC SucceX-Force 5,8 g 800 mW VTX Stack

IFlight
BLITZ F7 OSD Flight Controller W/ BLITZ E45S 4-IN-1 ESC SucceX-Force 5.8g 800mW
VTX Stack 2-6S for RC FPV Racing Drone
Description：
FC
// BLITZ F7 V1.1 Flight Controller
Top Features:
Improved circuit
design, better components and lower electrical noise!
DJI HD VTX Connector
(Plug-and-Play / No soldering required)
FC indicator LEDs for visual
debugging
With LC filter
Specifications:
MCU: STM32 F722
Gyro:
BMI270
Barometer: DPS310
OSD Chip: AT7456E
Flash: 32MB (Blackbox
flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C serial: SDA /
SLA pads
Smartaudio / IRC Tramp VTX protocol supported
LED controller:
Yes
Beeper pad: Yes
Firmware target: IFRC-IFLIGHT_BLITZ_F722
Mount
pattern: 30.5*30.5mm / 4mm PCB hole diameter
Dimensions: 36.5*35
mm
Weight: 7.8g
Wiring suggestion:
UART 1 for VTX HD /
Analog
UART 2 for a Receiver
UART 3/4/5 for GPS or other sensors that
require a serial port
UART 6 for ESC Telemetry
Tips
1. F722 MCU has
an inner inverter.
2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any
unused UART_RX，we suggest you connect to Uart_RX2
3. Frsky SmartPort，Tramp
& Smartaudio can be connected to any unused UART_TX，we suggest you connect
to Uart_TX1
4. F.port can be connected to any unused UART_TX，we suggest you
connect to Uart_TX2
ESC // BLITZ E45S 4-IN-1 2-6S
ESC
Specification:
Supports: DShot150/300/600/MultiShot/ OneShot
etc.
Mounting Holes: 30.5*30.5mm/Φ4mm
Supports 2-6S lipo
input
Telemetry Output: NO
Target: QH-40 16.7
Current sensor:
Yes
Constant: 45 Amps
Current rate: 200
Burst: 55 Amps
Weight:
14.7g
MCU: BB21
BEC: NO
VTX // SucceX Force 5.8GHz 800mW VTX
Adjustable
Features:
Stable output power
5 Power levels up to
800mW;
48 Channels (including Raceband)
Fast frequency lock, no startup
interference with other pilots
Built-in output power self-check
functionality
VTX telemetry with IRC Tramp protocol
Tips:
VTX is
set to 25mW by default! Power levels above 25mW require a HAM license or have to
be approved by local authorities! Please ensure you're flying legal frequencies
and use our prepared Betaflight VTX tables according to your
region.
Specs:
Input voltage: 7V～36V (@12V/380mA@800mW)
Video
standard: NTSC /PAL
Output voltage/ Max current: 5V 1A
Power levels:
PIT/25mW/100mW/400mW/800mW
Power draw @12V input current: 40mA@PIT MODE,
95mA@25mW, 185mA@100mW，250mA@400mW, 380mA@800mW
Channels: 48 (including
Raceband)
Small size: 36*36*3mm
Mounting pattern: 30.5x30.5 (4x
M3)
Lightweight: 7.5g (excluding antenna)
VTX telemetry: IRC
Tramp
Betaflight IRC Tramp Configuration: Please download the attached
VTX table for Betaflight!
All our VTX tables can also be found here:
LINK
IRC Tramp VTX table values: 25/25mW, 100/100mW, 400/400mW, 600/800mW